Through this webpage, choose online customer service communication, or message board. Leave your needs and get limited time discounts, up to 10% off, saving you a fortune. This discount has an indefinite period, and places are limited on a first-come, first-served basis.
We support various payment methods:
T/T payment
VISA
paypal
MasterCard
Alipay etc
Save time in your buying process.
The company's products have passed multiple national
certifications:
for example:
United States: ASME
EU: CE
Eastern Europe: EAC
Russia: GOST
Singapore: MOMO
etc
Buy products, buy with confidence, use with confidence
Domestic hot water and heating series: gas hot water boiler, vacuum hot water boiler, vertical atmospheric pressure hot water boiler, electric hot water boiler Factory use, high temperature steam: wns fuel gas steam boiler, szs water tube steam boiler, vertical steam boiler, electric steam boiler
FANGKUAI is founded in 1998, which is a clean fuel boiler enterprise integrating R&D, manufacturing, sales and service. In the past 20 years of development and innovation, the company has grown into a global enterprise, and its products have been exported to more than 80 countries including Russia, Mongolia and Thailand, and have established long-lasting cooperative relations with local enterprises!
If you are interested in our company or products, you can contact with us through online consulting, demand table submission, e-mails and telephones. Our staff shall wholeheartedly provide product information, application knowledge and good service for you.
How to set and adjust the boiler pressure - Heating Help
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
How to Set Hot Water or Steam Heating System Pressure Get Price
The process is simple: Locate the two filling valves. Open one of the two valves completely Slowly open the second valve, watching how the needle (or indicator light system) on the pressure gauge responds Let the needle reach the middle of …Get Price
Wait for the water pressure to reach between 1 and 1.5 on the pressure gauge. Once it has, shut off both valves one after the other. Switch the boiler back on and, if needed, press the reset button. Undo both ends of the filling loop and remove from the pipes. Be careful to catch any water spillage and remember to keep the loop in a safe place.Get Price
On the boiler pressure issue, 25 psi is high for a residential boiler. Normal operating pressure is around or below 15 psi. You have a pressure relief valve that is set to discharge @ 30 psi. If your dad was setting the pressure higher than that, the relief valve would open to drop the pressure back under 30 psi.Get Price
Oct 10, 2007 · The pressurestat "on" setting is the point where the heating element indicator light illuminates. These readings are slightly higher (lower) than the gauge's lowest (highest) point because the pressure continues to drop below the lower setpoint for a moment after the heating element comes on, and momentarily rises past the higher setpoint after Get Price
How to Increase Your Boiler Pressure | M&N Heating & PlumbingGet Price
Feb 01, 2013 · Boilers - Home Heating Steam and Hot Water Systems - Oil Pump Pressure - Factory Setting? - My service tech installed a new pump (Beckett/Suntec a2ea-6528) on a Beckett AFG burner that calls for 140# pressure. I asked him twice if he was going to set/check the pressure and he insisted twice that it comes factory set atGet Price
Standard Cold Operating Pressure. The standard cold water operating pressure of most U.S. and Canadian hot water boilers is 12 pounds per square inch (psi). If the boiler pressure drops below 12 psi, the valve will allow new water into the unit to …Get Price
Jan 02, 2008 · Mt PRV pops at 20 psi So I set the boiler right around 12 psi. You do have a pressure relief valve on the boiler don't you? You can adjust this pressure using this valve. That is how I adjust mine when needed. But if yours is swinging that much from cold to hot, I don't think this adjustment is going to help you.Get Price
Jun 24, 2017 · When the steam pressure in the boiler drops 10 psi, the boiler will start up automatically. When the pressure reaches to 250 psi, it will shutdown the boiler. In case of modulating pressuretrol it controls the boiler firing at high and low within adjusted range with the help of modulating motor linked with fuel valve.Get Price
Feb 04, 2019 · The guys who service my boiler didn't really have a preference as to which way it should be. Right now I have it wired so the boiler can heat the water only if the house thermostat is calling for heat in the house. That way I don't need to shut down the boiler in summer. It simply won't heat the water until the house cools enough to call for heat.Get Price
Jan 07, 2022 · Low boiler pressure. It's a good idea to keep an eye on your boiler's pressure gauge quite often, because low boiler pressure can lead to your central heating system failing to function properly. To check the boiler pressure, simply take a look at the built-in pressure gauge, if you see anything below 1 then you may have an issue.Get Price
Feb 26, 2019 · You start the boiler and allow the pressure to build. Once the pressure reaches your set point, 10 Psig, the burner shuts off. The burner stays off until the pressure inside the boiler drops to the differential (2 psi) setting minus …Get Price
The ideal boiler pressure should be between 1 to 1.5 bars on your pressure gauge when your heating is switched off. Around 2 bars is a normal pressure level when your boiler is active/heating up. Anything below 0.5 is too low and must be replaced.Get Price
When the heating is turned on your boiler pressure should be between 1.5 and 2 bar. Most boilers will highlight this area on the pressure gauge in green to help you see if the needle is pointing to the correct amount of pressure. Some boilers will also have the critical zones below 1 and above 2 marked in red to help you identify any issues.Get Price
Dec 19, 2021 · Your boiler has a gauge to check the heating pressure. The ideal pressure is 12psi (pounds per square inch). It is perfectfor staying the psi in between 12-15. The modern boiler endures almost 30 psi pressure. But this more pressure can leak and open up the whole valve system, later spoil it. Now check this machine. Step 1: Power off the boiler Get Price
Feb 03, 2007 · My 35 year old Homart Gas fired Steam Boiler from time to time won't kick in. When it works, it's fine for a few days to weeks, but sometimes when the weather gets real cold, it will come up in the morning, but then stop running and not …Get Price
Note: The operating pressure of the boiler cannot exceed the maximum operating pressure of the boiler casting. Under standing how to adjust and check system fill pressures can aid in trouble shooting noisy operation, no heat and inadequate heat on top floors of unusually high buildings using residential hot water boilers.Get Price
The position set when the boiler was installed is sometimes shown by a red indicator needle. On most digital gauges, you'll see a flashing pressure reading, if there's a low (or high) pressure warning. If your boiler pressure reads less than 1 bar, it's possible that you might have lost water from the system, which needs to be replaced.Get Price
The steps for repressurising a boiler using a filling key instead of a filling loop are slightly different: 1. Turn off the boiler. 2. Insert the filling key into the keyhole and unlock it. 3. Turn the valve next to the key until water flows through it. The …Get Price
What should your boiler pressure be when the heating is on? Most, if not all, pressure gauges have coloured markers for the safe and unsafe conditions of the pressure inside of your appliance. Ideally, when the boiler is on, the pressure should be between 1,5 to 2 bars, and when it's not working – 1 to 1.5 bars.Get Price
Winter position = heating and hot water . 3: Hot water temperature is adjusted by moving this selector knob. 4: Boiler pressure. Keep the needle between the 1 and 2 of the pressure gauge, it is shaded in the picture to help illustrate it clearly (the needle will rise and fall as the boiler heats up and cools down).Get Price
EFFICIENT HEATING SYSTEM OPERATION The boiler is a high efficiency, condensing appliance which will automatically adjust its output to match the demand for heat. Therefore gas consumption is reduced as the heat demand is reduced. The boiler condenses water from the flue gases when operating most efficiently.Get Price
Dec 30, 2019 · High pressure can result from the boiler temperature being set too high. Higher pressures generally cause automatic shutdowns. Modern boilers have built-in pressure release valves. These generally trip at 30 psi and release excess steam to bring the pressure back to normal. It'll also kick off the power to your boiler.Get Price
Sep 03, 2019 · Sealed heating systems, as are almost always found with combi boilers, need to have their pressure checked and topped up from time to time. In most cases the pressure gauge will be on the front of the boiler and should register 1.0 to 1.5 Bar. Over time the pressure will fall. How quickly depends on how leaky the system is.Get Price
The central heating system is sealed (closed) and pressurised, usually to between 1 and 1.5 bar (cold). This pressure is the boiler pressure. When the system heats up, the water expands, taking up more space. The boiler pressure will rise a little, normally by up to half a bar.Get Price
The central heating system is sealed (closed) and pressurised, usually to between 1 and 1.5 bar (cold). This pressure is the boiler pressure. When the system heats up, the water expands, taking up more space. The boiler pressure will rise a …Get Price
The water feed system to your boiler has a pressure reducer valve. That reduces the pressure delivered from the city (or even a well system) so that the loop is not over-pressurized. The setting on most pressure reducer valves is 12 PSI. That is likely the pressure on your boiler system.Get Price
Fig schematic diagram of a boiler room scientific the heating system probe location and 1 pulverizers 2 steam drum 3 layout advice help wall with parts for dummy s electrical engineering 123 as seen in monitoring feedback on piping main equipment introduction house cad cadblocksfree blocks free automation scheme generator mective sealed central systems open …Get Price
Boiler Layout..11 2 Boiler Manifold Dimensions switch to the 120V power supply outside of the boiler room. Ensure main power supply to equipment, the heating system, and all external controls have been deactivated. Condensate must drain from the flue pipe to the boiler.Get Price